PDF《承认书》

承认书APPROVAL SHEET 客户名称: Customer 深圳市福昌辉科技有限公司 产品名称: Part Name 绕线型片式电感器 Wire Wound Chip inductor 产品规格: Specification FHW1008UC1R0KGT 版本号: Version No.

16.01 日期: DATE 2017-7-20 制造 Manufacturer 客户 Customer 拟制 Draft by 审核 Checked by 确认 Approve by 检验 Check by 审核 Checked by 批准 Approval by 林晓华 徐雪枫 区军沛 Page

1 of

12 序号 No 目录TABLE OF CONTENTS

1 履历表Resume

2 外形尺寸与内部结构 Dimension &

Inner-configuration

3 产品品名构成 Product Spec. Model

4 电性能参数表 Electrical Characteristics List

5 可靠性试验项目 Reliability Testing Items

6 产品包装 Packaging

7 推荐焊接条件 Recommend Soldering Conditions

8 清洗 Cleaning

9 存储要求 Storage Requirements

10 ODS(消耗臭氧层物质)的使用情况 Usage Of ODS

11 注意事项 Notes Page

2 of

12 1. 履历表Resume 版本 Version No. 修改明细Modify Details 日期 Date 16.01 首次发行 Initial issue 2016-04-01 Page

3 of

12 2 外形尺寸与内部结构 Dimension &

Inner-configuration: 序号 No. 部位 Component 材料 Material

1 瓷/磁芯Core 陶瓷芯电感Ceramic Core:陶瓷体Al2O3 铁氧体芯电感Ferrite Core:镍锌铁氧体Ni-Zn ferrite

2 电极Electrode 分类 Type 底层 Layout

0 中层 Layout

1 表层 Layout

2 陶瓷芯电感 Ceramic core 钨或钼锰 W or Mo-Mn 镍Ni金或锡 Au or Sn 铁氧体芯电感 Ferrite core 银Ag 镍Ni锡Sn

3 漆包线wire 铜Cu

4 包封层encapsulation layer 树脂Epoxy

5 标识Marking 树脂Epoxy 单位Unit:mm(inch) 型号 Size L (Max) W (Max) T (Max) A B C D E 2520(1008) 2.92(0.115) 2.79(0.110) 2.10(0.083) 2.00(0.079) 0.50(0.020) 2.54(0.100) 1.02(0.040) 1.27(0.050)

3 产品品名构成 Product Spec. Model ① 绕线型片式电感器系列 Wire Wound Inductor Series;

② 外形尺寸 Dimensions:1008;

③ 芯片类型 Material:UC;

④ 标称电感量 Inductance: 1R0=1000nH;

⑤ 标称电感值偏差 Tolerance:F---±1%;

G---±2%;

J---±5%;

K---±10%;

⑥ 电极表面镀层材料 Terminal:G---金端头 Gold;

⑦ 包装类型 Packaging type:T---卷带盘装 Tape&

Reel;

B---散装 Bulk. Page

4 of

12 4 电性能参数表 Electrical Characteristics List 型号规格 Part NO. 客户料号 Customer P/N 误差 范围 Tolerance (%) 标称 感量 Inducta nce (nH) 感量测试 频率 Ls Test frequency (MHz) Q 值(Min) Q 值测试 频率 Test frequency (MHz) 直流 电阻 Rdc (Ω)max 测试 电压 Test voltag e(mV) 自谐振 频率 SRF (MHz)min 额定电流 Idc (mA)max FHW1008UC1R0KGT / ±10

1000 25

35 50 1.75

500 210

370 Page

5 of

12 5 可靠性试验项目 Reliability Testing Items 序号 No. 项目 Items 要求 Requirements 试验方法及备注 Test Methods and Remarks

1 工作温度范围 Operating Temperature Range FHW-UC/HC series:-40℃~+125℃ FHW-UF/IF/QF/HF series:-40℃~+85℃

2 可焊性 Solder ability 外观不发生变化;

超过 90%的焊锡覆盖在 端电极表面 There shall be no case deformation or change in appearance. The metalized area must have more than 90% solder coverage. 在245±5℃ 熔融的焊锡(96.5Sn/3.0Ag/0.5Cu)中浸置 5±1 秒钟. Dip pads in flux and dip in solder pot(96.5Sn/3.0Ag/0.5Cu)at 245±5℃ for 5±1 seconds.

3 耐焊接热 Soldering Heat Resistance 外观不发生变化;

感量变化不超过±5%;

Q 值变化不超过±10%. There shall be no case deformation or change in appearance. Inductance shall not change more than ±5%;

Q shall not change more than±10%. 在260±5℃ 熔融的焊锡(96.5Sn/3.0Ag/0.5Cu)中浸置 10±1 秒钟. Dip pads in flux and dip in solder pot(96.5Sn/3.0Ag/0.5Cu)at 260±5℃ for 10±1 seconds.

4 介质耐压 Dielectric Withstand Voltage 外观不发生变化;

无击穿现象 here shall be no case deformation or change in appearance.No evidence of voltage breakdown. 在电感器端子和包封层间施加 500V 交 流电压,持续一分钟. Input 500v AC between the electrodes and the resin of inductor and keep on one minute.

5 绝缘电阻 Insulation Resistance 铁氧体芯: ≥500MΩ 陶瓷芯:≥1000 MΩ Ferrite: ≥500MΩ Ceramic: ≥1000 MΩ 在电感器端子和包封层间施加 100V 直 流电压,持续一分钟. Input 100v DC between the electrodes and the resin of inductor and keep on one minute.

6 端电极附着力 (推力测试) Component Adhesion (Push of test) 绕线型片式电感器: Wire Wound Chip inductor: 0402UC series:≥0.45Kg 0603UF series:≥0.9Kg 0603UC series、 0805UF series: ≥1.3 Kg Other series: ≥2Kg Page

6 of

12 序号 No. 项目 Items 要求 Requirements 试验方法及备注 Test Methods and Remarks

7 过载 Over Loading 外观不发生变化;

电感器不开路. There shall be no case deformation or change in appearance. Inductors shall not have a open winding. 将规定额定电流

2 倍的直流电流加于电 感器,其电流误差为±2%,,

保持

5 分钟. Direct current of rating current between inductor terminals , Direct current error ±2%, and keep on five minutes.

8 振动Vibration 无开路或短路;

感量变化不超过±5%;

Q 值变化不超过±10%. Inductors shall not have a shorted or open winding. Inductance shall not change more than ±5%. Q shall not change more than±10%. 振幅 1.5mm,频率 10~55Hz,每个方向 保持

2 小时. Inductors shall be subjected to vibration of 1.5mm amplitude frequency 10~55Hz (10Hz to 55Hz to 10Hz in a period of

1 minute) for

2 hours in each of three(X、Y、Z) axes.

9 温度变化 Temperature Change 外观不发生变化;

感量变化不超过±5%;

Q 值变化不超过±10% There shall be no case deformation or change in appearance. Inductance shall not change more than ±5%. Q shall not change more than±10%. FHW-UC/HC 系列: +125℃

60 分钟 ← → -40℃

60 分,钟循环

5 次;

FHW-UF/IF/QF/HF 系列: +85℃

60 分钟 ←→ -40℃

60 分,钟循环

5 次;

室温下放置一小时后测试. FHW-UC/HC series :+125℃ 60minutes ←→ -40℃ 60minutes

5 Cycles;

FHW-UF/IF/QF/HF series : +85℃ 60minutes ←→ -40℃ 60minutes

5 Cycles;

Inductors are to be tested after

1 hour at room temperature.

10 高温 High temperature 外观不发生变化;

感量变化不超过±5%;

Q 值变化不超过±10% There shall be no case deformation or change in appearance. Inductance shall not change more than ±5%. Q shall not change more than ±10%. FHW-UC/HC 系列产品放置于温度+125 ±5℃的环境中存放 96±2 小时;

FHW-UF/IF/QF/HF 系列产品放置于温度 +85±5℃的环境中存放 96±2 小时;

在室温下放置

1 小时后进行测试. FHW-UC/HC series shall be subjected to +125±5℃ for 96±2 hours;

FHW-UF/IF/QF/HF series shall be subjected to +85±5℃ for 96±2 hours;

Inductors are to be tested after one hour at room temperature. Page

7 of

12 序号 No. 项目 Items 要求 Requirements 试验方法及备注 Test Methods and Remarks

11 低温 Low temperature 外观不发生变化;

感量变化不超过±5%;

Q 值变化不超过±10% There shall be no case deformation or change in appearance. Inductance shall not change more than ±5%. Q shall not change more than±10% 将电感器放置于温度-40±2℃的环境 中存放 96±2 小时,然后在室温下放置

1 小时后进行测试. Inductors shall be subjected to -40±2℃for 96±2 hours. Inductors are to be tested after one hour at room temperature.

12 恒定湿热 Static Humidity 外观不发生变化;

感量变化不超过±5%;

Q 值变化不超过±10% There shall be no case deformation or change in appearance. Inductance shall not change more than ±5%. Q shall not change more than±10%. 将电感器放置在于湿度 93±3%,温度

50 ±2℃的环境中存放 96±2 小时, 经过

1 小时的风干后进行测试. Inductors shall be subjected to ........