PDF《JN516x-EK001 Evaluation Kit》

2014 9 1.2 Kit Contents In the kit, you will find the following components (numbers refer to Figure 4): 1. Linksys Wireless-N Broadband Router (WRT160NL) 2. 12V DC power supply unit (universal type) for Linksys router 3.

2 antennas with SMA connectors for Linksys router 4. RJ45 Ethernet cable for Linksys router 5. USB Type-A extension cable for Linksys router 6.

2 JN5168 USB Dongles with integrated antenna (DR1198) 7.

4 Carrier Boards (DR1174): ?

1 pre-fitted with a Generic Expansion Board (DR1199) and a? JN5168 standard-power module with uFL connector (JN5168-001-T03) ?

3 pre-fitted with a Lighting/Sensor Expansion Board (DR1175) and a JN5168 standard-power module - two with integrated antenna ? (JN5168-001-T00), one with uFL connector (JN5168-001-T03) 8. Generic Expansion Board (DR1199) 9. LCD Expansion Board (DR1215) 10.

4 JN5168 high-power modules with uFL connector: ?

2 JN5168-001-T05 modules for worldwide use ?

2 JN5168-001-T06 modules for use in North America (FCC and IC) only 11. Remote Control Unit (DR1159), based on the JN5168 wireless microcontroller 12. Programming Dongle (DR1128) for Remote Control Unit 13.

4 antennas with fly-leads for modules with uFL connectors 14. 5-way 2.1mm daisy-chain power extender-cable 15.

3 '

USB A to Mini B'

cables 16.

2 packs of AAA batteries As noted above, the four Carrier boards are pre-fitted with expansion boards and JN5168-based modules. Details of the supplied combinations are provided in Table

1 on page 10. Note: A JN5168-001-T0y component comprises a JN5168-001-M0y module mounted on a (short) Mezzanine Board of the type DR1179. It is labelled JN5168-001-M0y. Chapter

1 Introduction to the Evaluation Kit

10 ? NXP Laboratories UK

2014 JN-UG-3093 v1.4 * Each module is mounted on a DR1179 Mezzanine Board, which is mounted on the Carrier Board. The pre-fitted JN5168 modules, the JN5168 USB Dongles and the Remote Control Unit of this evaluation kit are pre-programmed with the relevant binaries for the JenNet-IP Smart Home Demonstration (see Section 1.4). However, the JN5168 high- power modules are not pre-programmed with any application. The Linksys router is pre-programmed with an NXP firmware update. Figure 4: JN516x-EK001 Evaluation Kit Components Expansion Board Fitted Module Fitted * Antenna Provision on Module

1 Lighting/Sensor (DR1175) JN5168-001-T00 Integrated antenna

2 Lighting/Sensor (DR1175) JN5168-001-T00 Integrated antenna

3 Lighting/Sensor (DR1175) JN5168-001-T03 uFL connector for external antenna

4 Generic (DR1199) JN5168-001-T03 uFL connector for external antenna Table 1: Supplied Carrier Board Configurations JN516x-EK001 Evaluation Kit User Guide JN-UG-3093 v1.4 ? NXP Laboratories UK

2014 11 1.3 Kit Hardware This section details the hardware devices supplied in the JN516x-EK001 Evaluation Kit (see Section 1.2 for full kit contents): ? Remote Control Unit (and Programming Dongle) - see Section 1.3.1 ? Carrier Boards - see Section 1.3.2 ? Lighting/Sensor Expansion Boards - see Section 1.3.3 ? Generic Expansion Boards - see Section 1.3.4 ? LCD Expansion Board - see Section 1.3.5 ? JN5168 modules - see Section 1.3.4 ? JN5168 USB Dongles - see Section 1.3.7 ? Linksys router - see Section 1.3.8 1.3.1 Remote Control Unit (DR1159) The Remote Control Unit (part number: DR1159) is designed around the JN5168 device and features a 16-button capacitive-touch keypad. The unit is designed as a wireless network node which can be used to control other nodes of ........