PDF《LITE-ON TECHNOLOGY》

LITE-ON TECHNOLOGY CORPORATION P r o p e r t y o f L i t e - O n O n l y Features * Meet ROHS, Green Product.

* Reverse mount Chip LED. * Ultra bright AlInGaP Chip LED. * Package in 8mm tape on

7 diameter reels. * Compatible with automatic placement equipment. * Compatible with infrared and vapor phase reflow solder process. * EIA STD package. * I.C. compatible. Package Dimensions + Part No. Lens Source Color LTST-C230KRKT Water Clear AllnGaP Red Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.10 mm (.004 ) unless otherwise noted. Part No. : LTST-C230KRKT Page :

1 of

11 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION P r o p e r t y o f L i t e - O n O n l y Absolute Maximum Ratings At Ta=25℃ Parameter LTST-C230KRKT Unit Power Dissipation

75 mW Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width)

80 mA DC Forward Current

30 mA Derating Linear From 50°C 0.4 mA/°C Reverse Voltage

5 V Operating Temperature Range -55°C to + 85°C Storage Temperature Range -55°C to + 85°C Wave Soldering Condition 260°C For

5 Seconds Infrared Soldering Condition 260°C For

5 Seconds Vapor Phase Soldering Condition 215°C For

3 Minutes Part No. : LTST-C230KRKT Page :

2 of

11 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION P r o p e r t y o f L i t e - O n O n l y Suggestion Profile: (1) Suggestion IR Reflow Profile For Normal Process (2) Suggestion IR Reflow Profile For Pb Free Process R e c o m m e n d e d P ro file B e tw e e n A sse m b le A n d H e a t-R e sista n c e L in e T he P rofile is availa ble th at m u st to u se S n A g C u so ld e r pa ste Part No. : LTST-C230KRKT Page :

3 of

11 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION P r o p e r t y o f L i t e - O n O n l y Electrical Optical Characteristics At Ta=25℃ Parameter Symbol Part No. LTST- Min. Typ. Max. Unit Test Condition Luminous Intensity IV C230KRKT 18.0 54.0 mcd IF = 20mA Note

1 Viewing Angle 2θ1/2 C230KRKT

130 deg Note

2 (Fig.6) Peak Emission Wavelength λP C230KRKT

639 nm Measurement @Peak (Fig.1) Dominant Wavelength λd C230KRKT

631 nm Note

3 Spectral Line Half-Width Δλ C230KRKT

20 nm Forward Voltage VF C230KRKT 2.0 2.4 V IF = 20mA Reverse Current IR C230KRKT

10 μA VR = 5V Capacitance C C230KRKT

40 PF VF =

0 f = 1MHZ Notes: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Part No. : LTST-C230KRKT Page :

4 of

11 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION P r o p e r t y o f L i t e - O n O n l y Bin Code List Part No. : LTST-C230KRKT Page :

5 of

11 BNS-OD-C131/A4 Luminous Intensity Unit : mcd @20mA Bin Code Min. Max. M 18.0 28.0 N 28.0 45.0 P 45.0 71.0 Q 71.0 112.0 R 112.0 180.0 Tolerance on each Intensity bin is +/-15% LITE-ON TECHNOLOGY CORPORATION P r o p e r t y o f L i t e - O n O n l y Typical Electrical / Optical Characteristics Curves (25 °C Ambient Temperature Unless Otherwise Noted) Part No. : LTST-C230KRKT Page :

6 of

11 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION P r o p e r t y o f L i t e - O n O n l y Cleaning Do not use unspecified chemical liquid to clean LED they could harm the package. If clean is necessary, immerse the LED in ethyl alcohol or in isopropyl alcohol at normal temperature for less one minute. Suggest Soldering Pad Dimensions Package Dimensions Of Tape And Reel Notes: 1. All dimensions are in millimeters (inches). Part No. : LTST-C230KRKT Page :