PDF《SS-P》

125 VAC) 100,000 operations min. (20 operations/min,

30 VDC) SS-01P: 200,000 operations min. (20 operations/min) Weight Approx. 1.6 g (for pin plunger models) Model SS-3P SS-01P Rated voltage Item Resistive load

125 VAC

3 A 0.1 A

30 VDC

3 A 0.1 A Rated Voltage SS-3P SS-01P

125 VAC

3 A 0.1 A

30 VDC

3 A 0.1 A Rated Voltage SS-3P SS-01P

125 VAC

3 A 0.1 A

30 VDC

3 A 0.1 A Item SS-3P SS-01P Specification Rivet Crossbar Material Silver alloy Gold alloy Gap (standard value) 0.5 mm Minimum applicable load (see note)

160 mA at

5 VDC

1 mA at

5 VDC Subminiature Basic Switch SS-P

105 Engineering Data Mounting Holes PCB Mounting Dimensions (Reference - uneven spacing) PCB Mounting Dimensions (Reference - even spacing) Panel Mounting All switches may be panel mounted using M2.3 mounting screws with plane washers or spring washers to securely mount the switch. Tighten the screws to a torque of 0.23 to 0.26 N・m Contact Form Dimensions Terminals Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. Terminal plate thickness is 0.5 mm for all models. Solder Terminals Quick-connect Terminals (#110) PCB Terminals (Uneven pitch) PCB Terminals (Even pitch) 16.1±0.1 Three, 1.35 to 1.5 dia. 8.8±0.1 7.62±0.1 7.62±0.1 Three, 1.35 to 1.5 dia. 9.5±0.1 Two, 2.4-dia. mounting holes or M2.3 screw holes COM NO NC SPDT 15.5 Three, 1.6-dia. holes 8.55 3.3±0.1 0.5 7.55±0.2 2.15 7.3 3-2.8 3.3±0.1 0.5 7.55±0.2

11 7.1 7.6±0.2 7.6±0.2 3-0.8 3-1.2 8.8±0.2 16.1±0.2 3.3±0.1 0.5 1.3 3.9 1.8 7.55±0.2 (5.25) 1.85 3-0.8 3-1.2 7.62±0.2 7.62±0.2 3.3±0.1 0.5 1.3 3.9 1.8 7.55±0.2 (4.82)

106 Subminiature Basic Switch SS-P Dimensions and Operating Characteristics Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following illustrations are for solder terminal models. Refer to "Terminals" for models with quick-connect terminals (#110) and PCB terminals. 3. The operating characteristics are for operation in the A direction( ) Pin Plunger Models SS-3GP SS-01GP 19.8±0.2 5.15 9.5±0.1 15.5 Three, 1.6 dia. holes 8.55 3.3±0.1 3.5 7.7 0.5 6.4±0.2 6.9 7.55±0.2

2 PT OP 2.35+0.075 dia. ?0.05 2.5±0.07 dia. 2.15 7.3 A 2.35+0.075 ?0.05 Characteristics SS-3GP SS-01GP OF max.

153 gf RF min.

20 gf PT max. 0.6 mm OT min. 0.4 mm MD max. 0.15 mm OP 8.4 ± 0.3 mm Hinge Lever Models SS-3GLP SS-01GLP 19.8±0.2 5.15 9.5±0.1 15.5 8.55 FP OP 0.5 6.4±0.2 6.9 14.5 t=0.3 Stainless-steel lever 2.15 7.3 A 3.3±0.1 7.7 Three, 1.6 dia. holes 2.35+0.075 ?0.05 2.35+0.075 dia. ?0.05 2.5±0.07 dia. 3.6 Characteristics SS-3GLP SS-01GLP OF max.

51 gf RF min.

5 gf OT min. 1.0 mm MD max. 0.8 mm FP max. 13.6 mm OP 8.8 ± 0.8 mm Simulated Roller Lever Models SS-3GL13P SS-01GL13P 5.15 15.5 8.55 FP OP 0.5 6.9 R1.2 15.8 2.15 7.3 A 7.7 19.8±0.2 9.5±0.1 6.4±0.2 t=0.3 Stainless-steel lever 3.3±0.1 Three, 1.6 dia. holes 2.35+0.075 ?0.05 2.35+0.075 dia. ?0.05 2.5±0.07 dia. 3.6 Characteristics SS-3GL13P SS-01GL13P OF max.

51 gf RF min.

5 gf OT min. 1.0 mm MD max. 0.8 mm FP max. 15.5 mm OP 10.7 ± 0.8 mm Subminiature Basic Switch SS-P

107 Precautions Correct Use Mounting Mount the Switch onto a flat surface. Mounting on an uneven surface may cause deformation of the Switch, resulting in faulty operation or breakage in the housing. Operating Stroke Setting Take particular care in setting the operating stroke for the pin plunger models. Make sure that the operating stroke is 60% to 90% of the rated OT distance. Do not operate the actuator exceeding the OT dis- tance, otherwise the life expectancy of the Switch may be shortened. Using Microloads Using a model for ordinary loads to switch microloads may result in faulty operation. Instead, use the models that are designed for micro- loads and that operate in the following range;