PDF《2010-04-22》

DVP-1130430-02 5011687001-E2X1 2010-04-22 -

1 - ENGLISH Thank you for choosing Delta'

s DVP series PLC.

DVP06XA-E2 mixed analog input/output module receives external

4 points of analog input signals (voltage or current) and converts them into 16-bit digital signals. For the analog signal output, DVP06XA-E2 receives

2 groups of 16-bit digital data coming from the PLC MPU and converts the digital data into

2 points of analog output signals (voltage or current). In addition, you can access the data in the module by applying FROM/TO instructions or read the average value or write the output value of channels directly by using MOV instruction (Please refer to allocation of special registers D9900 ~ D9999). a This instruction sheet provides only information on the electrical specification, general functions, installation and wiring. For detailed program design and applicable instructions, please refer to DVP-ES2 Operation Manual: Modules . For details of the optional peripheral, please refer to the instruction sheet enclosed in it. a This is an OPEN TYPE I/O module and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required for operating the enclosure) in case danger and damage on the device may occur. a DO NOT connect the input AC power supply to any of the I/O terminals;

otherwise serious damage may occur. Check all the wiring again before switching on the power. Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference. ? Product Profile &

Dimension [ Figure

1 ]

70 62

106 98

78 90 61.5

110 06XA -E2 4A I/ 2AO Direct mounting hole Model Name Terminal No. I/O module connection port Terminal No. Power / AD / Error indicators Removable I/O terminal I/O module connection port I/O module clip Mounting slot (35mm) (Unit: mm) ? External Wiring y Input: Active-type CH1 1M

250 V1+ I1+ VI1- CH1 CH4 V4+ I4+ VI4- CH4 *3 *2 AG 0V 24V DC/DC +15V -15V AG FE FE Voltage input Current input Shielded cable*1 Shielded cable*1 Terminal of power module Grounding (100 or less) Converter [ Figure

2 ] 1M 1M

250 AG 1M + - UIN + - UIN -

2 - y Input: Passive-type CH1 1M

250 V1+ I1+ VI1- CH1 CH4 V4+ I4+ VI4- CH4 *3 *2 AG 0V 24V DC/DC +15V -15V AG FE FE Voltage input Current input Shielded cable*1 Shielded cable*1 Terminal of power module Grounding (100 or less) Converter [ Figure

3 ] 1M 1M

250 AG 1M - + UIN - + y Output VO1 IO1 AG CH5 *5 CH5 Voltage output AC motor drive, recorder, scale valve... Shielded cable*4 VO2 IO2 AG CH6 CH6 0V 24V DC24V DC/DC +15V -15V AG Class

3 grounding (100 or less) converter Shielded cable*4 Current output Terminal of power module AC motor drive, recorder, scale valve... [ Figure

4 ] *1: When performing analog input, please isolate other power wirings. *2: When the XA module is connected to current signals, make sure you short-circuit V+ and I+ terminals. *3: If the ripples at the loaded input terminal are too significant that causes noise interference on the wiring, connect the wiring to 0.1 ~ 0.47μF 25V capacitor. *4: When performing analog output, please isolate other power wirings. *5: If the ripples at the loaded output terminal are too significant that causes noise interference on the wiring, connect the wiring to 0.1 ~ 0.47μF 25V capacitor. *6: Please connect the terminal on both the power module and XA module to the system earth point and ground the system contact or connect it to the cover of power distribution cabinet. ? I/O Terminal Layout FE FE FE 0V 24V DVP06XA-E2 (4AI/2AO) IO1 VO1 VI2- I2+ V2+ VI1- I1+ V1+ VI4- I4+ V4+ VI3- I3+ V3+ AG IO2 VO2 AG ? Electrical Specifications DVP06XA-E2 Power supply voltage 24VDC (20.4VDC ~ 28.8VDC) (-15% ~ +20%) Max. rated power consumption 2.5W, supplied by external power source Connector European standard removable terminal block (Pin pitch: 5mm) -