PDF《INNOLUX》

1 44 LD I Latches the polarity of outputs and switches the new data to outputs INNOLUX SPEC NO.: A080-03-TT-31 PAGE: 4/28 The copyright belongs to InnoLux. Any unauthorized use is prohibited.

45 B5 I Blue data (MSB)

46 B4 I Blue data

47 B3 I Blue data

48 B2 I Blue data

49 B1 I Blue data

50 B0 I Blue data (LSB)

51 R/L I Right/ left selection Note 1,2

52 V1 I Gamma voltage level

1 53 V4 I Gamma voltage level

4 54 V7 I Gamma voltage level

7 55 V10 I Gamma voltage level

10 56 V12 I Gamma voltage level

12 57 V13 I Gamma voltage level

13 58 AVDD P Voltage for analog circuit

59 GND P Power ground

60 VCOM I Common voltage I: input, O: output, P: Power Note 1: Selection of scanning mode Setting of scan control input IN/OUT state for start pulse U/D R/L STVD STVU STHR STHL Scanning direction GND VCC O I O I Up to down, left to right VCC GND I O I O Down to up, right to left GND GND O I I O Up to down, right to left VCC VCC I O O I Down to up, left to right INNOLUX SPEC NO.: A080-03-TT-31 PAGE: 5/28 The copyright belongs to InnoLux. Any unauthorized use is prohibited. Note 2: Definition of scanning direction. Refer to the figure as below: Left Right Up Down INNOLUX SPEC NO.: A080-03-TT-31 PAGE: 6/28 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 2.2. Backlight Unit Section Pin No. Symbol I/O Function Remark

1 HI P Power supply for backlight unit Pink

2 GND - Ground for backlight unit White INNOLUX SPEC NO.: A080-03-TT-31 PAGE: 7/28 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 3. Operation Specifications 3.1. Absolute Maximum Rating (GND=AVSS=0V, Note 2) Values Symbol Min. Max. Unit Remark VCC -0.3

5 V AVDD -0.5 13.5 V VGH -0.3

18 V VGL -15 0.3 V Power voltage VGH-VGL -

33 V V1~V7 0.4 AVDD AVDD+0.3 V Note

1 Input signal voltage V8~V14 -0.3 0.6AVDD V Note

1 Operation Temperature TOP -20

70 ℃ Storage Temperature TST -30

80 ℃ Note 1: AVDD - 0.1≥V1≥V2≥V3≥V4≥V5≥V6≥V7≥V8≥V9≥V10≥V11≥V12≥V13≥V14≥AVSS + 0.1 Note 2: The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme case, the module may be permanently destroyed. INNOLUX SPEC NO.: A080-03-TT-31 PAGE: 8/28 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 3.1.1. Typical Operation Conditions (GND=AVSS=0V, Note 1) Values Item Symbol Min. Typ. Max. Un it Remark VCC 3.0 3.3 3.6 V AVDD 9.8

10 10.2 V VGH 14.3

15 15.7 V Power voltage VGL -10.5 -10 -9.5 V VCOM - (4.124) - V V1~V7 0.4 AVDD - AVDD -0.1 V Input signal voltage V8~V14 0.1 - 0.6 AVDD V Input logic high voltage VIH 0.7VCC - VCC V Input logic low voltage VIL

0 - 0.3VCC V Note 1: Be sure to apply VCC and VGL to the LCD first, and then apply VGH. INNOLUX SPEC NO.: A080-03-TT-31 PAGE: 9/28 The copyright belongs to InnoLux. Any unauthorized us........