PDF《安装说明书》

机台开关 Installation lntroduction 安装说明书 2015/04 0.

5-1mm 机台面 安装位置示意图 Installation description chart. TK-A

2 One end of under-knife stick on tabletop, the other end float 0.5~1mm from tabletop. 2.下刀与机台面需一端贴合,另一端浮起约0.5-1mm 1.装上TK斩刀 Install TK Positioning clip 下刀 Tabletop 机台开关 机台开关

3、汽缸气压管连接图与电路配置图 The instruction for connect tube.

3 TK-A (A).将气动组装上后,向左方调整,再将 After installs pneumatic set please adjust it towards left side then fasten screw. 螺丝锁紧. 安装位置示意图 Installation description chart. Accomplish as below picture. (C).完成如图.

4、安装气动组 Installation of pneumatic set. 红白黑Table 桌板 Table 桌板

24 23

14 30

34 29

10 13

12 9

11 34

25 16

15 31

26 27 TK-分析图

19 7

8 4

3 2

7 17

20 22

21 19

2 4

6 3

5 TK-Detail drawing

1 18

20 6

33 32

32 29

28 28 TK-A

4 35

30 36

37 37

38 39 Washer Square connection slice Under Knife TK-04 下刀

16 盘型垫片 SW0702

36 SW0111

38 37 电磁铁 保护片 保护片 VG2700A-DVCA VG2700A-DVC39-A

32 35

34 33

29 30

31 28

27 TK-05 SW0605 VG2700A-DVC07 VG2700A-DVC14 TKA-05 TK-06

21 24

26 25

22 23

19 20

17 18 Electromagnctic valve 上刀 六角半圆头螺丝 轴心 弹簧 上刀座 轴 弹簧垫片 本体

6 TK-03 SW0204 TKA-04 TKA-03 TK-01 TK-12 TK-02-1

11 14

15 12

13 8

10 9

7 TKA-02 SW0711-A TKA-01 物料编号 Part.No.

3 4

5 1

2 序号Ref.No. Shaft Spring Washer 名称Description

1 M4

1 2

1 M8

1 1

2 1

1 2

2 1

1 1

2 M14

1 1

1 1

1 1

1 1

2 1

1 1 Amt.Req. 单位用量 E-7 E型扣环 E shape retaining ψ7 六角螺帽 Hexagon nut SW0512 无头承窝螺丝 Headless socket screw M14x14L M5x8L 空气管接头 气闸软管接头 Air brake hose coupling Connector 六角螺帽 Hexagon nut 连杆端轴承 VC2700E-UTE02 Coupling rod end bearing Tube-03-600 Tube-02-1240 气闸软管 气闸软管 Air brake hose Air brake hose ψ6xψ4 ψ8xψ5 固定座 Fixed seat - 内六角螺丝 Crossed flat head screw Compressed air bottle 空压瓶 VG2700A-DVC13-3 M4x30 - TK-零件分析表 TK-Detail drawing Crossed wooden screw Wooden screw Minus flat head screw Minus flat head screw Hexagon socket screw Hexagon socket screw Spring 十字头木螺钉 SW0940 脚踏开关 PS-A LFE-15 Pedal switch 外六角螺丝 六角头木螺钉 无头螺丝 一字平头螺丝 一字平头螺丝 六角承窝螺丝 TK-08 SW1009 SW0909 SW0505 SW0305 SW0303 轴SW0124 Hexagon screw Axle Headless socket screw Main plate Protector piece Protector piece Upper knife Upper knife seat 锥型垫片 六角承窝螺丝 SW0714 SW0136 Axle Taper washer

2 M3.5X11

2 1 M5x10L - M4x7L M4x5L

4 1

2 2

3 M5x16L

2 M6x25L

2 2 M6 Axle 轴Cylinder 传动汽缸 M5x5L 脚踏开关座

(二) Pedal switch seat(II) SM6(黑)

5 TK-A

39 2

2 请使用正确的磨 磨剪刀面 大剪刀只 "V"型槽为磨直刀口,两面皆可磨. 赠品使用方法:

1、重复环保万用绳

2、磨剪刀器使用方法:如图面来回磨擦数次即可. 将万用绳尾端往后拉紧即可. 锁 物件 拉 将万用绳尾端往后拉,一拨即开. 一拨即开 解 向后拨 若尾端太短,可先将一根万用绳连接在原万 拉锁用绳尾端,再往后拉,一拨即开. 使用方法: Caution for eye injuries ! 剪刀面,剪刀图 示面为磨剪刀面. 请注意正确的握姿:磨刀时手严禁握在磨刀口的正下方! How to use the gift : Reusable eco-friendly universaltie 小心刺伤眼睛! How to use : Lock Item Pull Pull the strap to fasten. Unlock 物件 Item Open with one pick Pick backward Pull Pull the universal tie backward and pick to open 物件 Item 解Unlock 向后拨 Pick backward 拉Pull Lock How to use Scissirs sharpener :Rubbung back and forth several timesas figures. Carefully usewith correct position : Strictly forbid to hold under the sharpener ! For scissors Please choose the rightside for scissors or knifes as the signal. Bothside "V" notch is for knifes. Shears only for single side sharpen 限单边磨 If its too short to open,connect another piece of universal tie to make it longer anel follow the same step as abore.