PDF《LPS100-M Series》

LPS100-M Series

150 Watts Total Power:

80 -

150 Watts Input Voltage:

90 -

264 Vac

120 -

300 Vdc # of Outputs: Single SPECIAL FEATURES ? ? Medical and ITE safety approvals, 2X MOPP ? ? Active power factor correction ? ? 2" x 4" footprint ? ? Less than 1U high ? ? EN61000-3-2 compliant ? ? Remote sense ? ? Power fail ? ? Adjustable main output ? ? Built-in Class B EMI filter ? ? Overvoltage protection ? ? Overload protection ? ? Thermal overload protection ? ? Isolated

12 V fan output ? ? LPX100 Enclosure kit available ? ? POE isolation on main output of LPS109-M SAFETY ? ? TUV 60950, 60601-1 ? ? UL 60950, 60601-1 ? ? cULus 60950, 60601-1 ? ? CB Certificate & report ? ? CE Mark (LVD) ? ? CQC Mark Electrical Specifications Input Input ra?nge

90 -

264 Vac;

120 -

300 Vdc Frequency

47 -

63 Hz Inrush current

50 A max.

, cold start @

25 °C Efficiency 88% typical at full load EMI/RFI FCC Class B conducted;

CISPR22 Class B conducted;

EN55022 Class B conducted;

VDE0878PT3 Class B conducted Safety ground leakage current

275 μA @ 50/60 Hz,

264 Vac input Output Maximum power

100 W for convection (80 W for LPS102-M);

150 W with

30 CFM forced air (120 W for LPS102-M) Adjustment range ± 10% minimum on the main outputs Fan output

12 V @

1 A isolated, ± 10% Hold-up time

10 ms @

150 W load,

120 Vac input Overload protection Short circuit protection on all outputs. Case overload protected @ 110-160% above rating Overvoltage protection 15-35% above nominal output Logical Control Power failure Open collector logic signal goes high 100-500 msec after main output;

it goes low at least

6 msec before loss of regulation Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. Data Sheet Environmental Specifications Operating temperature 0° to

50 °C ambient derate each output as 2.5% per degree from 50° to

70 °C. (-20 °C startup5 ) Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4;

-2, -3, -4, -5, -6, -8, -11 Level

3 Humidity Operating;

non-condensing 10% to 95% RH Vibration IEC 60068-2-6 to the levels of IEC721-3-2 MTBF calculated 534,000 hours at full load and

25 °C ambient conditions,

230 V input, Bellcore Ordering Information Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30CFM Forced Air Peak Load Regulation2 Ripple P/P (PARD)3 LPS102-M

5 V

0 A

16 A

24 A

30 A ± 2%

50 mV LPS103-M

12 V

0 A 8.3 A 12.5 A

14 A ± 2%

120 mV LPS104-M

15 V

0 A 6.7 A

10 A

11 A ± 2%

150 mV LPS105-M

24 V

0 A 4.2A 6.3 A

7 A ± 2%

240 mV LPS108-M

48 V

0 A 2.1 A 3.1 A 3.5 A ± 2%

480 mV LPS109-M

54 V

0 A 1.85 A 2.8 A 3.1 A ± 2%

540 mV 1. Peak current lasting <

30 seconds with a maximum 10% duty cycle. 2. At

25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with

20 MHz bandwidth and

10 ?F (tantalum capacitor) in parallel with a 0.1 ?F capacitor at rated line voltage and load ranges. 4. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. 5. At